Key takeaways
- The ARCTIC TP-3 is a very soft, cuttable blue silicone thermal pad for VRAM, SSDs, and GPUs. Read the specs, stacking rules, and who should skip it.
The ARCTIC TP-3 is a premium thermal pad built for one job: moving heat across the uneven gaps between hot chips and their heatsinks. It is a soft blue silicone pad with a special thermally conductive filler, aimed at memory chips, graphics cards, SSDs, and other components where a rigid pad would leave air pockets behind. One honest note: the TP-3 comes in several sizes and thicknesses under separate listings, and no published source pins down the exact size, thickness, or pack count behind this ASIN, so variant-specific fields below are marked not stated.
What makes the TP-3 interesting is its softness. At 55 Shore OO it is far softer than most thermal pads, so it compresses into height differences between neighbouring chips instead of pressing hard against them. It is also stackable: two 1 mm pads become a 2 mm pad without a performance penalty. The pad is cuttable, electrically insulating, and non-adhesive, so it trims to size and lifts off cleanly.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
The ARCTIC TP-3 is a very soft, stackable silicone thermal pad for VRAM, SSDs, GPUs, and chipsets, best suited to uneven gaps where a firmer pad would not seat evenly. ARCTIC publishes no thermal conductivity figure for it, so judge it on softness, thickness choice, and fit. Confirm the exact size and thickness on the listing before ordering.
Key Specs
| Spec | Value |
|---|---|
| Brand | ARCTIC |
| Model | TP-3 |
| Material | Silicone with a special filler |
| Colour | Blue |
| Hardness | 55 Shore OO |
| Thickness options | 0.5 mm, 1.0 mm, 1.5 mm |
| Size options (line) | 100 x 100 mm, 200 x 100 mm, 120 x 20 mm |
| Size for this ASIN | not stated |
| Thickness for this ASIN | not stated |
| Pack quantity for this ASIN | not stated |
| Model number for this ASIN | not stated |
| UPC for this ASIN | not stated |
| Item weight | not stated |
| Continuous use temperature | -40 to 150 degrees C |
| Specific gravity | 3.4 g per cubic cm |
| Dielectric constant at 1 MHz | 5.19 |
| Volume resistance | 2.69 x 10 to the power of 12 ohm-cm |
| Flammability rating | UL 94 V-0 |
| Thermal conductivity (manufacturer figure) | not published by ARCTIC |
| Electrically insulating | Yes |
| Adhesive | No |
| Cuttable | Yes |
| Stackable | Yes, to 2.0 mm without performance loss |
| Country of origin | not stated |
| First available date for this ASIN | not stated |
| Warranty | not stated |
Who It’s For
The TP-3 is for anyone replacing the thermal pads inside a graphics card, a laptop, a console, or an SSD enclosure. Its best use is on VRAM modules and other chips that sit at slightly different heights, because the soft material fills those small steps instead of bridging over them. It also suits first-time pad swappers: the pad cuts cleanly with scissors and does not stick to the chip. It suits repairs where the original pad thickness is unknown, since stacking covers the range.
Who Should Skip It
Buyers who need a published thermal conductivity figure for a design calculation should skip the TP-3. ARCTIC deliberately publishes no watt-per-metre-kelvin figure for this pad and explains in its own FAQ why it does not. The TP-3 is also the wrong choice for gaps under about 0.2 mm, where ARCTIC itself recommends thermal paste instead of a pad. It is non-adhesive by design, so it will not hold a heatsink in place on its own, and it is rated only to 150 degrees C continuous use.
How It Compares With Typical Alternatives
Against thermal paste, the TP-3 wins on gap filling and loses on thin interfaces. Paste is the right choice for a flat CPU or GPU die where the gap is a fraction of a millimetre, because paste forms the thinnest possible layer. A pad is the right choice where two surfaces are separated by a visible gap or sit at different heights, which paste cannot bridge at all.
Against harder thermal pads, the TP-3 trades firmness for conformity. A firm pad holds its shape and can feel easier to place, but it presses harder on tall chips and may leave a thin air gap over shorter ones. The TP-3 compresses more readily, so it conforms to uneven surfaces and puts less mechanical load on the assembly.
Against thermal putty, the TP-3 is cleaner and more repeatable. Putty conforms to any shape and fills the deepest gaps, but it is messy to apply and hard to remove cleanly. A cut pad gives a defined thickness and a tidy edge, which makes reassembly predictable. Against the older ARCTIC TP-2, the TP-3 is the clear successor: the TP-2 is end of life, and independent testing found the TP-3 softer with a better polymer matrix.
One point deserves emphasis because it confuses many buyers. ARCTIC publishes no thermal conductivity figure for the TP-3, while many rival pads advertise large numbers on the box. An independent laboratory roundup that measured pads under controlled conditions found the TP-3 delivered about 5.47 watts per metre-kelvin of effective conductivity at about 800 micrometres of compressed thickness. That is an independent measurement, not a manufacturer rating.
Frequently Asked Questions
What thickness of TP-3 should I buy?
Measure the gap first. ARCTIC’s guidance is to pick a pad slightly thicker than the gap so it compresses into full contact: a 1.5 mm pad for about a 1.2 mm gap, and two 1.5 mm pads for about a 2.6 mm gap. A 0.5 mm pad can compress to 0.3 mm and bridge height differences of up to 0.2 mm. If the gap is under about 0.2 mm, use thermal paste instead.
Can I stack TP-3 pads?
Yes. ARCTIC states that TP-3 pads stack to 2.0 mm without performance loss, so two 1 mm pads can serve as a 2 mm pad. This is useful when the exact gap depth is uncertain or when only thinner pads are on hand.
Is the TP-3 electrically conductive?
No. The TP-3 is electrically insulating, with a volume resistance of 2.69 x 10 to the power of 12 ohm-cm and a dielectric constant of 5.19 at 1 MHz. That means it can sit safely across closely packed components without shorting them.
Does the TP-3 leave residue or stick to components?
No. The pad is non-adhesive and easy to handle, so it lifts off cleanly when a card is opened again later. Its softness does mean it can tear if pulled at an angle, so lift it straight up and replace any pad that has torn during removal.
Final Verdict
The ARCTIC TP-3 is a well-judged thermal pad for the job it is designed to do: bridging uneven gaps between hot chips and heatsinks without stressing the board. Its softness, stackability, and clean removal are real advantages over firmer pads, and its electrical insulation and UL 94 V-0 flammability rating cover the safety side. The main weakness in this listing is information, not the product: the exact size, thickness, and pack count behind this ASIN could not be confirmed from published sources, so buyers must check the listing and match the variant to their measured gap.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.

Write Your Review
No reviews yet. Be the first to share your experience!